Updated October 2026 · Written by the DeckStainIQ team at The Stain Depot
What you'll need
- A deck cleaner and brightener, or a stripper if there's an old film finish (see which one you need)
- Your stain (find the right one) and enough of it (gallon calculator)
- A garden hose or pressure washer on a low setting, and a stiff deck brush
- A natural bristle stain brush, stain pad or roller, plus a brush for gaps and edges
- Plastic sheeting or tarps for plants and siding
Step 1: Pick your days
You need about four dry days: one to clean, two for the wood to dry, and one to stain, plus a day or two after for the stain to set. Most stains want air and surface temperatures between about 50°F and 85–90°F, so check your can. Stain in the shade or on an overcast day. Hot sun flashes the stain dry before it can soak in.
Step 2: Clean
Wet the deck, apply the cleaner, let it sit as the label says (don't let it dry), scrub, and rinse. This removes dirt, mildew and gray, sun-damaged wood fibers. If there's an old solid stain, paint or peeling finish, use a stripper instead. Penetrating stain can't soak through it.

Step 3: Brighten
Brightener neutralizes the cleaner or stripper and opens up the wood so stain soaks in evenly. It also takes out the dark tannin stains cedar and redwood are known for. Kits like the TWP Restore-A-Deck or Woodrich Cleaner & Brightener include both steps.
Step 4: Let it dry
Give the wood at least two dry days. Then sprinkle water on a few boards. If it soaks in quickly, you're ready. If it beads, wait longer. Staining damp wood is one of the most common reasons stain fails.
Step 5: Test a spot
Every deck takes color differently. Try your color on a board in an out-of-the-way spot and let it dry before committing.
Step 6: Apply
- Cover plants, siding and anything you don't want stained.
- Do the railings and vertical parts first, then the floor, so drips on the floor get covered.
- Work two or three boards at a time along their full length. Stopping mid-board leaves lap marks.
- Apply an even coat and work it in. If you roll or spray, back-brush right after.
- Follow your product's coat instructions. TWP, for example, goes on wet on wet: if the first coat soaks in within 15–30 minutes, add a second before it dries. One-coat products like Sikkens SRD stop at one.
- On hardwoods, wipe off any oil that hasn't soaked in within 30–45 minutes.
Carpenter bees a problem? Mix Bee Gone into the stain before you start.

Step 7: Let it cure
Keep people, pets and furniture off until the stain is dry, usually 24–48 hours, and longer in cool or humid weather. Check your can for the exact times.
Safety: oily rags
Rags and pads soaked in oil-based stain can heat up and catch fire on their own. Lay them flat outside to dry, or soak them in water in a closed metal container before throwing them away.
Common questions
Do I have to clean my deck before staining?
Yes. Dirt, mildew and gray wood fibers keep stain from soaking in, and the stain will wear off early.
How long after washing a deck can I stain it?
Usually at least two dry days. Sprinkle water on the boards: if it soaks in quickly, the wood is ready.
Should I use a brush, roller or sprayer?
A brush or stain pad works stain into the wood best. Rollers and sprayers are faster on big decks, but back-brush right after so the stain soaks in evenly.
What temperature is best for staining a deck?
Most stains want about 50°F to 85–90°F, out of direct sun, with no rain for two days. Check the label of your stain.
Not sure which is right for your deck?
Our Stain Finder asks five quick questions and gives you a top pick and a runner-up that can ship to your state.
DeckStainIQ is run by the team at The Stain Depot, which sells the products mentioned here. We explain why we recommend each one.